Polyester resin base flame retardant adhesives
Adhesive series for fixing electronic devices with outstanding electrical properties and approval of flame retardant grade (V-0) and UL Standard.
Products Category Adhesive
 
SC608Z2 Series

Product Name

 SC608 Z2 series

Suitable use

 For fixing electronic devices and insulation

Application

 Computers / AV / Cellular phones

Features
  • UL94 V-0 certified (No. E63260)
  • UL746C(File No. MH15485)
  • An excellent electrical insulator.
  • Highly viscous and thixotropic, the product can be easily applied to a vertical surface without threading that may lead to an untidy appearance.
  • SC608LVZ2 is identical to SC608Z2 except for a lower viscosity.
 

Specifications
Product Name SC608Z2 SC608LVZ2
Main component Polyester resin base
Color White
Viscosity(Pa.s) 50 to 125Pa.s 7 to 10Pa.s
Solid content(%) 57 to 64% 50 to 54%
Specific gravity About 1.3 About 1.2
Diluent Toluene, MEK
Container 180ml Tube/18kg can 180ml Tube/1kg or 18kg can

Application Example
Application Example: SC608Z2 series
 Insulation and bonding in electronic component assembly lines
  • Fixing diskrete parts onto a PCB
  • Fixing lead wires
  • Sealing coils
Utilization of insulation performance
  • Insulation for prevention of electric shock
  • Insulating connectors

※For bonding of difficult materials (such as polyethylene, polypropylene, polycarbonate, or soft PVC), please contact us beforehand.

※For bonding of materials soluble in toluene, MEK (such as polycarbonate, Noryl, ABS or acrylics), please contact us beforehand.
Top of page

Technical Data
1.Adhesive property Shear strength test
Results
Specific gravity Initial(N) Substrate
Shear strength 190.1CF Polystyrene/Polystyrene

Initial= 100°C 24H
CF= Cohesive failure of adhesive layer
2.Electrical property  
Test Piece Condition
Specimen size: 0.5 mm-thick sheet
Initial condition: Drying for 2 hrs at 100°C after being left at RT for 72 hrs
  • Instrument: Kikusui 875 AZ LERA CURRENT 1
  • AC Voltage applied: Increased in 0.5-KV increments in 30 seconds; the highest voltage that did not induce dielectric breakdown was recorded
  • DC Voltage applied: Started at 3 KV; increased in 0.5-KV increments in 30 seconds
Results
Loading condition Voltage applied Initial(KV) After aging(KV) Aging condition
100°C AC 9.5 9.5 500hr(100°C, 60°C 90%)
(-30°C x 3hr/100°C x 3hr) x 10
(Cycling test)
60°C 90% 9.5 9.5
Cycling test 9.5 9.5
100°C DC 10.0 or higher 10.0 or higher
60°C 90% 10.0 or higher 10.0 or higher
Cycling test 10.0 or higher 10.0 or higher
3.Volume resistance  
Test Piece Condition
Specimen size: 0.5 mm-thick sheet
Results
Loading condition Initial(Ω-cm) After aging(Ω-cm) Aging condition
100°C 1.6 x 1015 2.2 x 1015 500hr(100°C,60°C90%)
(-30°C x 3hr/100°C x 3hr)x10
(Cycling test)
60°C 90% 1.6 x 1015 1.3 x 1015
Cycling test 1.6 x 1015 4.8 x 1015

※Data reported above is for SC608Z2. SC608LVZ2 differs only in the viscosity and solid content; the hardening characteristics are practically the same as those of SC608Z2 (within the tolerance range).

4.Surface resistance  
Test Piece Condition
Specimen size: Test circuit pattern (after JIS Z3197) was formed by etching a 35µm copper foil/glass-epoxy circuit board, and subsequently covered with the adhesive 0.2 mm thick (wet).
Instrument: Yokogawa HP 4329A high-resistance meter
Results
Loading condition Initial(Ω) After aging(Ω) Aging condition
100°C 2.7 x 1015 1.1 x 1015 500hr(100°C, 60°C 90%)
(-30°C x 3hr/100°C x 3hr)x10
(Cycling test)
60°C90% 2.7 x 1015 0.4 x 1014
Cycling test 2.7 x 1015 4.8 x 1015
5.Impact force resistance  
Test Piece Condition
Circular bonding: Capacitor bonded on the entire periphery of the bottom
Partial bonding: Capacitor bonding at two points on the periphery of the bottom (bonded area = half of the periphery)
  • A capacitor 6.8 g in weight was bonded onto a glass-epoxy circuit board (5 x 5 cm in size).The assembly was aged for seven days at 20°C in an atmosphere of 65% in RH. The assembly was then dropped from a height of one meter.
Results
Circular bonding Partial bonding
Joint intact in 100 times falling Joint intact in 100 times falling
6.Corrosion  
Results

The product applied on a silver-plated polycarbonate board to form a 0.2-mm (wet) film did not corrode the substrate for 200 hrs at 100°C.

※Data reported above is for SC608Z2. SC608LVZ2 differs only in the viscosity and solid content; the hardening characteristics are practically the same as those of SC608Z2 (within the tolerance range).
Top of page
Notes  
  1. Check before operation
    Check the relevant material safety data sheet (MSDS) and instruction manuals for precautions required for operation.
  2. Operation environment
    • Keep ignition sources away.
    • Use a local ventilator to ensure sufficient air circulation.
  3. First aid
    • Learn action to take from the MSDS and instruction manuals.
    • In case of eye contact, vapor inhalation or swallowing, seek medical attention immediately.
  4. Storage
    Store the product in a tightly closed container in a predetermined place at room temperatures avoiding direct sunlight.
  5. Prohibition of unintended use
    Never use the product except as an adhesive.
Top of page
caution The technical data in this document, which was acquired based on reliable tests, does not guarantee full performance as per the documentation in any instance. Users assume total responsibility and risk for use of this product for any purpose under any usage conditions.